Engines cannot be started

[RicardoLVFR]

oh you have to link the images here on this forum

[Wolfgang04041981]

Ah, sorry, here you go:

https://ibb.co/jZhCgnt
https://ibb.co/PMCbvVZ

[RicardoLVFR]

sorry just seeing this now. Can't understand why this is happening. This is the only A32x variant you have?

[Wolfgang04041981]

Yes, no other mods or planes have been installed.
Could it be somehow related to the Airport? So far I only tried LOWW (Vienna).

[Wolfgang04041981]

Had some time last weekend and tried to start the Engines at Manchester Airport which worked perfectly fine.
I don't know why it doesn't work at Vienna but at least it's not a general fault.
Just wanted to let you know...

[7heAngryVe7eran]

Had some time last weekend and tried to start the Engines at Manchester Airport which worked perfectly fine.
I don't know why it doesn't work at Vienna but at least it's not a general fault.
Just wanted to let you know...

Maybe you will find this helpful.

How I begin all of my flights...

Virtual Airline Route - CHOSEN
SimBrief Flight Plan - CREATED
SimBrief Downloader - FLIGHTPLAN DOWNLOADED AS MSFS .PLN
MSFS STARTED
LatinVFR A320 - AIRCRAFT SELECTED. TAIL NUMBER, CALLSIGN, and FLIGHT NUMBER SELECTED.
Airport and Parking - CHOSEN
START FLIGHT
Freeware Pushback App (or GSX) - CONNECT JETWAY
Interior Lights - AS NEEDED
Fuel and Payload - SELECTED IAW VIRTUAL AIRLINE ROUTE BRIEFING
Batteries 1 and 2 - ON
External Power - ON
Engine 1 and 2 Generators -OFF
Engine 1 and 2 Bleed Air - OFF
APU Gen - OFF
ADIR Switches (3) - NAV
Beacon Light - ON
Probe/Window Heat - ON
No Smoking Sign - ON
GSX - BOARD PASSENGERS
FSUIPC7 - LOAD PLAN (.PLN From SimBrief Downloader)
ATC - ATIS
Baro - SET TO ATIS ALTITUDE
ATC - CLEARANCE IFR
AP Altitude - SET IAW ATC CLEARANCE ALTITUDE
AP Heading - SET IAW ATC CLEARANCE TAKEOFF RUNWAY. NOTE CORRECT PUSHBACK DIRECTION.
MCDU INIT PAGE - IRS INIT, CO RTE, FROM/TO, ALTN, FLT NBR, CI, and CRZ FL CHECKED
MCDU PERF PAGE - V1, VR, V2, TRANS ALT, FLAPS/THS CHECKED
MCDU F-PLN PAGE - DEPARTURE SET IAW ATC CLEARANCE. ROUTE CHECKED WITH MFD and CLEANED UP
BOARDING COMPLETE
ATC - GROUND TAXI
FUEL PUMPS - ALL ON
APU MASTER SW - ON
APU - START
APU BLEED - ON
APU GEN - ON
External Power - OFF
Fasten Seatbelt Sign - ON
Strobe Lights - AUTO
Freeware Pushback App (or GSX) - REMOVE JETWAY
Freeware Pushback App (or GSX) - PUSHBACK
Parking Brake - OFF
ENG Switch - IGN/START
ENG 2 Switch - ON. WAIT FOR GOOD ENGINE START.
ENG 2 Bleed - ON
ENG 2 Generator - ON
ENG 1 Switch - ON. WAIT FOR GOOD ENGINE START.
ENG 1 Bleed - ON
ENG 1 Generator - ON
APU Master SW - OFF
APU Bleed - OFF
APU Generator - OFF
Flaps - SET
Trims - SET
Anti Ice - AS NEEDED
Exterior Lights - AS NEEDED

I know this is more information than you probably need, but I didn't want to miss any of my own steps in trying to help.

[7heAngryVe7eran]

This topic is now locked.